Delivered Australia-wide Australian support
The Home Bed closed, in a plaster-walled living room with an oak floor and a linen armchair.
The Home Bed in the white finish, canopy open, both banks of panels lit.
White
The Home Bed set up in a spare room, canopy open and lit.
A woman lying inside the bed, panels lit above and below her.
The Home Bed in the silver grey finish, canopy open.
The bed open and lit in a converted garage, weights and a rolled mat to one side.
The bed lit in a plaster-walled room at dawn, low sun across an oak floor.
The power inlet and illuminated switch on the shell.
Mid-session, the panels lit above and below.
The cooling fans built into the shell.
Two people in a plaster-walled room, one stepping out of the bed.
40 minA full session, lying down
25 mW/cm²At the surface you lie on
~$1/wkTo run, at four sessions a week

Irradiance measured at 15 cm, at the lying surface, not the panel face. Running cost from ~0.9 kWh a session at four sessions a week on a typical Australian tariff.

Eight weeks to decide

Run the protocol. Feel nothing and we collect it and refund you.

Delivered Australia-wide

To your kerb or ground-floor threshold. Moving it in is yours, or we quote it.

Two-year warranty

The whole machine. Claimed here, on an Australian number.

The detail

Everything you need to know

Every figure this bed is sold on, and the condition each one was measured under. The power it draws and what that costs to run. What the truck will and will not do, and the doorway it has to get through. What wears out, and exactly what the eight weeks cover. Open whichever one you came for.

A man lying on the bed mid-session, both banks of panels lit.
Full specification
Emitters
13,680
Rated life
100,000 hours
Wavelengths
633 · 660 · 810 · 850 · 940 nm
Output at the body
25 avg / 30 peak mW/cm² @ 15 cm
Session
40 minutes · ≈60 J/cm²
Power
1,360 W · ~5.7 A · 240 V
Supply
Standard 10 A point, AU plug fitted
Pulsing
1–10,000 Hz, per band
Programmes
Five presets and a manual mode
Dimensions
1987 × 860 × 890 mm
Weight
150 kg net · 234 kg crated
Shell / frame
ABS · carbon steel
Finish
White or silver grey
Noise
≈50 dB running · two fans
Certification
EN 60335-1 · EMC · RoHS
Warranty
2 years, whole machine
Availability
Limited monthly allocation
What’s included

The bed, delivery anywhere in Australia, the access survey, the printed eight-week protocol and two users configured on the machine. No consumables, no filters, no electrical work.

Not included: moving it into the room and setting it up. Delivery is to your kerb or a ground-floor threshold. It comes apart into two pieces, so most people arrange a second pair of hands. If you would rather we did it, ask and we will quote it before you order.

Size and access. Will it fit?
Unit
1987 × 860 × 890 mm
Weight, net
150 kg
Crate
2150 × 1050 × 1150 mm
Crated weight
234 kg
Opening needed
914 mm
Corner swing
2.15 m

A standard internal door is 820 mm, so 914 mm is the number to measure at the narrowest point on the route in. The crate needs 2.15 m of swing at every corner, because it does not bend.

It separates into two pieces. Two people can manage it on the flat; stairs are worth talking about first. We walk the route into your house with you on the phone before anything is dispatched, and if it will not take the crate we will say so. If you would rather not move it yourself, we will quote placement and setup with the bed.

The bed closed, beside a standard internal doorway, with a woman standing next to it for scale.
Delivery

We take a limited number of beds each month. When that month is committed the next window is the following one. You will know which window is yours when you order.

It arrives crated on a tail-lift and is left at your kerb or a ground-floor threshold. It is 234 kg in the crate and separates into two pieces, so the carry is a two-person job rather than a four-person one.

We will quote placement and setup if you want it. Either way we walk the route with you first, so the carry is planned rather than discovered.

Two installers easing the crated bed down the tail-lift of a truck on a suburban driveway.
Tail-lift to the kerb or a ground-floor threshold. It separates into two pieces from there.
Power and running cost
Draw
1,360 W · ~5.7 A · 240 V
Supply
Standard 10 A point, AU plug fitted
Per session
~0.9 kWh

An ordinary 10 A power point, and about a dollar a week at four sessions. The larger commercial beds need an electrician and a dedicated circuit. This one does not.

The eight weeks, and the warranty

Forty minutes, four times a week, for eight weeks. That is twenty-one hours, and it is the pattern the whole thing is written around. Keep it up, and if you have felt nothing we collect the bed and refund you. Collection is ours to arrange and ours to pay for.

Separately, two years on the whole machine. Where a part fails, we cover the part, the freight and the customs.

Care, cleaning and what wears out

Wipe the acrylic down after a session. It is the same surface as a shopfront window, so a cloth and an ordinary household cleaner is the whole routine. There is no cover to launder and no filter to change.

There are no lamps to replace. A tanning bed is relamped every few hundred hours and that is a running cost nobody quotes you. These are LEDs, rated to 100,000 hours. At four forty-minute sessions a week you would not reach that figure in a lifetime of owning it.

If a diode does fail, it is a warranty repair rather than a consumable. We would rather you knew which of those two this is before you buy.

How the light is measured
Wavelengths
633 · 660 · 810 · 850 · 940 nm
Emitters
13,680
At the body
25 avg / 30 peak mW/cm² @ 15 cm
Per session
≈60 J/cm²

Measured at the surface your body rests on, at 15 cm, not at the panel face. Measured on every unit before it ships. This is a wellness device rather than a medical device, so what is published here is what the machine does.

The bed open with a person lying full length, callouts marking face, torso and legs, light above and below.

Full-body coverage

13,680 LEDs, head to toe — your whole body in one session

The light runs the full length of the bed, above and below you. Face, back, shoulders, legs — everything gets covered at once, in one forty-minute lie-down. No aiming a panel at one spot at a time.

1,987 mm of light · both sides at once

Diagram: red light works at the skin surface, near-infrared reaches down to the muscle.

Five wavelengths

For younger-looking skin and faster recovery, in one session

The red light works at the surface, where the skin studies got their results. The near-infrared reaches deeper, into the muscle. Every session runs all five wavelengths together, so you never choose between them.

633 · 660 · 810 · 850 · 940 nm

Diagram: output measured at your skin where you lie, 25 mW/cmΒ², not at the panel face.

Serious output

Strong enough that forty minutes is all it takes

This is the difference between a bed and the panel on the wall. The output, measured at your skin rather than at the panel face, matches what the studies that got results actually used. Lie down, forty minutes, done.

25 mW/cm² at the lying surface · measured every unit before it ships

Close detail of the seam where the canopy meets the base, the gas strut at the hinge.

Built for every day

Toughened acrylic and steel — wipes clean in thirty seconds

You lie on a single solid sheet of toughened acrylic over a steel frame. It takes an adult without flexing, cleans with a cloth, and the canopy stays at whatever height you leave it.

Toughened acrylic · carbon steel frame · gas struts

A hand pushing the plug into an ordinary Australian wall socket, skirting board visible.

Plugs straight in

A normal socket — any room, no electrician

It runs from an ordinary 10 A power point with the Australian plug already fitted. Bedroom, spare room, garage — wherever it goes, it just plugs in. About a dollar a week to run.

1,360 W · standard 10 A socket · ~$1/week at 4 sessions

A hand reaching to the control panel, the screen lit.

One-button sessions

Set it once, then it’s one button

Five presets cover the usual routines. Pick yours in the first week, and every session after that is one press. Quiet enough to fall asleep under.

5 presets · ≈50 dB · 2 users configured

The evidence

What the research shows

31.6% less wrinkle volume

Randomised trial, 137 women, ten sessions over four weeks at 660 nm.

Strength back faster, less soreness

2025 review of fourteen studies: strength recovered faster at 24 and 48 hours, soreness down at 72 and 96.

$50–150 a session at a studio

Three a week is $7,800 to $23,400 a year. This is $17,000 once, and it is yours.

Parts of the research are mixed, especially on recovery, and we say so. Read the studies with citations.

The small things

Details you notice in week two

The canopy stays put

Gas struts hold it at whatever height you leave it.

Wipes clean

A cloth and whatever is under your sink.

Two users, configured

Both of you, at no extra cost.

Five presets

Most people pick one in the first week and leave it there.

Quiet enough for a podcast

Two fans at roughly 50 dB, about a quiet conversation.

Fits through a 914 mm opening

Delivered in two pieces, and we check your route on the phone first.

The plug is already fitted

An Australian 10 A plug, straight into the wall.

Five languages

On the control pad, switchable any time.

Carries an adult without flexing

Toughened acrylic over a carbon steel frame.

The guarantee

Eight weeks. Felt nothing, and we take it back.

Four sessions a week for eight weeks. Forty minutes each. Twenty-one hours in total. If at the end of it you have felt nothing, we collect the bed and refund you.

50% deposit

Secures your build slot. The balance is requested before delivery.

Delivered Australia-wide

Crated and insured, to your kerb or ground-floor threshold.

Australian support

Claimed here, on an Australian number, by the people who sold it.

01

You order

Online or on the phone, in full or with a 50% deposit. Eight weeks to decide starts the day it arrives.

02

We deliver

Crated and insured, kerbside or to a ground-floor threshold, anywhere in Australia. We confirm the route with you first.

03

You plug it in

An ordinary 10 A power point. No electrician, no rewiring, first session that evening.

A closer look

Walk through it with us

If you would rather see it than read about it, we will take you through the bed on a call. Where it goes, whether it fits through your door, and any questions this page has not answered.

Questions

Frequently asked

How much is it, and what does that include?

$17,000 AUD. That is the bed, delivery anywhere in Australia, the access survey, the protocol card and two-user setup. Delivery is kerbside or to a ground-floor threshold. Moving it into the room is yours to arrange, and we will quote that separately if you want us to do it.

What does it cost to run?

1,360 W for forty minutes is about 0.9 kWh a session. At four sessions a week that is roughly 3.6 kWh, or about a dollar a week on a typical Australian tariff.

Do I need an electrician?

No. It draws about 5.7 amps and runs from a standard 10 A power point, with an Australian plug already fitted. The larger commercial beds do need an electrician; this one does not.

Will it fit through my door?

It needs a 914 mm opening and it is 234 kg crated, delivered in two pieces. A standard internal door is 820 mm, so we check the route with you on the phone before anything ships.

How often do I have to use it?

Forty minutes, four times a week. That is the pattern the eight-week guarantee is written around. Below it the guarantee does not apply, because below it you have not given it a fair test.

Can more than one person use it?

Yes. Two users are configured on the machine, at no extra cost.

How is this different from the panel I already have?

Coverage, and it is arithmetic rather than opinion. A 30 by 60 cm panel lights about 0.18 m², on one side of you. This lights 1.5 to 1.8 m² at once, above and below. That is roughly ten times the skin in the same forty minutes, without holding still in front of something or turning over halfway.

If a panel did nothing for you, coverage is the first thing to check before you conclude the modality does not work. You can check it with a tape measure.

Is this the same as an infrared sauna?

No, and the mechanism is different rather than the intensity. A sauna works by raising the air temperature around you. This works by wavelength. It emits at five specific bands and does not heat the room.

They are not substitutes for each other and we would not tell you to replace one with the other. If you already own a sauna, this answers a different question.

What maintenance does it need?

Wipe the acrylic after a session. There is no cover to launder and no filter to change. There are no lamps to replace, which is the running cost nobody quotes you on a relamped tanning bed. These are LEDs rated to 100,000 hours.

What if it is damaged in transit?

It is insured for the whole journey. Photograph the crate before you sign for it, and tell us the same day if there is damage. Replacement is ours to arrange and ours to pay for.

Can I move it to another room myself?

It is 150 kg assembled. Two people can move it across a level floor. Stairs are a different job and worth planning rather than attempting. It runs from any ordinary power point, so the new room needs no electrical work.

How much room does it need around it?

The bed itself is 1987 × 860 mm on the floor. You also need to stand beside it and lift the canopy, so treat the working footprint as larger than the machine.

Getting it in is the tighter constraint: 810 mm at the narrowest point on the route and 2.15 m of swing at every corner. We walk that route with you before anything is dispatched.

How loud is it?

About 50 dB running, from two cooling fans. That is roughly a fridge. It is not silent and we would rather you planned for that than found out on the first session.

If a seller tells you a bed this size runs under 30 dB, ask how they measured it. 1,360 W of heat has to leave the machine somehow.

What is the warranty?

Two years on the whole machine. Where a part fails, we cover the part, the shipping and the customs.

Is it a medical device?

No. It is a wellness device and we do not make health claims about it. What is published here is what the machine does.

What if it does nothing for me?

Use it four times a week for the eight weeks, and if you have felt nothing we collect it and refund you.

Do you discount?

No seasonal sales, and no haggling. The published price is the same for everyone. The one exception is the welcome offer: $500 off your first bed when you join the list, which is our best price year-round rather than a discount that appears and disappears. It applies at checkout.

Talk to us

We’re here to help

Two questions about the room and the route in, and we will send you the full specification, your delivery window and a straight answer on whether it fits.

Ten minutes on the phone and you will know either way. If it is not right for your space we will say so rather than sell you one. Or email [email protected].

$17,000The Home Bed · eight weeks to decide